VERIZON BlackBerry Storm Unlock Instructions

1. Ensure the SIM Card that came pre-installed in the 9530 is inserted

2. Go to 'Manage Connections'

3. Click on 'Turn All Connections Off'

4. Go to 'Options'

5. Click on 'Advanced Options'

6. Click on 'SIM Card'

7. Type 'MEPD' (letters will not appear on-screen but a menu will pop up)

8. Type 'MEP2' (user will be prompted to enter MEP code)

9. Enter the unlock code (for example '1234567890123456')

10. Reboot device

11. Go to 'Manage Connections'

12. Click on 'Restore Connections'

13. Device is now unlocked

In case it gives an error you do the following:

Go to OPTIONS, Mobile network, And switch it from global to gsm

How to Enter Unlock Codes on BlackBerry Bold (9000), 8800, 8820, Curve (8300, 8310, 8320), Javelin (8900), Gemini (8520, 9300), & Onyx (9700):

Note: NO SIM is needed to unlock the phone. After phone is unlocked, remove the battery, insert SIM as desired and re-insert the battery. Phone MUST be restarted to use the new SIM card.

1) Power on

2) Go to Settings

3) Go to Options

4) Go to Advanced Options

5) Go to Sim Card

6) HOLD ALT and press: mep2 (Please note that you will NOT see what you type on the screen)

7) It will ask you for the unlock code. Enter it and then press trackball to confirm and your phone is unlocked!

How to Enter Unlock Codes on Bell Canada 9700 (Bold 2 Onyx):

Note: You must have a SIM card in your phone to complete these steps, I have found that this procedure works best with an Telus Sim card in the phone (can be active or inactive ). Make sure the phone is not displaying the low battery warning!

1) Power on

2) Go to Settings

3) Go to Options

4) Go to Advanced Options

5) Go to Sim Card

6) HOLD ALT and press: mep2 (Please note that you will NOT see what you type on the screen)

7) It will ask you for the mep2 code. Enter it and then press trackball to confirm.

8) After getting message 'Code Accepted', HOLD ALT and press the following: mep4 (Please note that you will NOT see what you type on the screen)

9 It will ask you for the mep4 code. Enter it and then press trackball to confirm. You phone is now unlocked!

How to Enter Unlock Codes on Telus Canada 9700 (Bold 2 Onyx):

Note: You must have a SIM card in your phone to complete these steps, I have found that this procedure works best with an Telus Sim card in the phone (can be active or inactive ). Make sure the phone is not displaying the low battery warning!

1) Power on

2) Go to Settings

3) Go to Options

4) Go to Advanced Options

5) Go to Sim Card

6) HOLD ALT and press: mep4 (Please note that you will NOT see what you type on the screen)

7) It will ask you for the unlock code. Enter it and then press trackball to confirm and your phone is unlocked!

How to Enter Unlock Codes on BlackBerry Pearl (8100, 8110, 8120, 8220):

Note: Remove any SIM that is currently in the phone. After phone is unlocked, remove the battery, insert SIM as desired and re-insert the battery. Phone MUST be restarted to use the new SIM card.

1) Power on

2) Go to Settings

3) Go to Options

4) Go to Advanced Options

5) Go to Sim Card

6) HOLD ALT (Left side Below @) and press: mepp2 (Please note that you will NOT see what you type on the screen)

7) It will ask you for the unlock code. Enter it and then press trackball to confirm and your phone is unlocked!

How to Enter Unlock Codes on BlackBerry 8830:

Note: SIM is REQUIRED to unlock the phone. SIM card can be inactive, doesn't need to active. After phone is unlocked, remove the battery, insert SIM as desired and re-insert the battery. Phone MUST be restarted to use the new SIM card.

No AT&T/T-mobile Usage: This is a dual-band phone, it will NOT work in North America but will work fine in Europe, Asia, South America where they use the other set of frequencies.

1) Power on

2) Go to Settings

3) Go to Options

4) Go to Advanced Options

5) Go to Sim Card

6) HOLD ALT and press: mep2 (Please note that you will NOT see what you type on the screen)

7) It will ask you for the unlock code. Enter it and then press trackball to confirm and your phone is unlocked!

Exception: If phone says Code Error and the attempts stay the same, start off with 10 attempts and still says 10 attempts after enter code, then continue with instructions, this is just a glitch on the phone.

How to Enter Unlock Codes on BlackBerry 8700/8700c/8700g:

Note: SIM is REQUIRED to unlock the phone. SIM card can be inactive, doesn't need to active. After phone is unlocked, remove the battery, insert SIM as desired and re-insert the battery. Phone MUST be restarted to use the new SIM card.

1) Power on

2) Go to Settings

3) Go to Options

4) Go to Advanced Options

5) Go to Sim Card

6) HOLD ALT and press: mepe (Please note that you will NOT see what you type on the screen)

6) It will ask you for the unlock code. Enter it and then press jog dial to confirm and your phone is unlocked!

How to Enter Unlock Code on a Cingular Blackjack

Step Action

Insert NON Cingular SIM into device

Power on the device

- Wait approximately 30 seconds until the Sim Lock application appears (the delay may be longer if the user has already attempted an unlock with the wrong code)

Enter the unlock code in the blank field

Press Ok

- If the unlock code is incorrect, an error dialog will appear.  After pressing Ok on this dialog, the user has to re-enter the unlock code after delays (see above in Device Specific Information)

- If the unlock code is correct, a success dialog will appear.

Press Ok

- The device is now unlocked and should continue booting

OR

Insert disallowed simcard (a simcard that the phone does not usaully accept) and enter unlock codes when prompted

NOTE: If you are unable to connect to service provider or unable to make out going calls or recieve messages, this has nothing to do with your phone being locked or not, you need to force the BlackJack to change to GSM mode, this can be done as follows:

Power on your Phone

Enter *#1546792*#

Select Option 3 Network & Call Settings

Select option 5 Network Mode

Select GSM

Without sim alternative i607 / Blackjack

Power on without sim, you will then get a message saying "SIM Failure" at the top of the screen.

Click "Done" then press the green button to get into the dial pad. Type in #7465625*638*

It will display "Enter Network Control Key" this is where you enter the 8 digit unlock code. Then click ok.

Your phone is now unlocked.

How to Enter 'Phone Freeze' Codes

1) With wrong sim enter 8 digit freeze code press ok button

2) Then enter network unlock code

Do NOT use: #7465625*638*code#

How to Enter Unlock Codes on a BlackJack (i607/i617), Jack i637, or Samsung T939 (Behold 2)

1) Power on with Incorrect SIM

2) Phone will prompt for Network Pin

3) Use Code provided and press OK

ERROR MESSAGE: WRONG PASSWORD or INVALID CODE - If you receive one of these messages when entering the code for the Blackjack, the phone is likely to be refurbished. In cases like these, unlocking of the phone by code cannot be done, only by machine. Many cell phone shops do carry hardware devices (NsPro Box) to remove the unlock from the phones.

NOTE: If you are unable to connect to service provider or unable to make out going calls or recieve messages, this has nothing to do with your phone being locked or not, you need to force the BlackJack to change to GSM mode, this can be done as follows:

1) Power on your Phone

2) Enter *#1546792*#

3) Select Option 3 Network & Call Settings

4) Select option 5 Network Mode

5) Select GSM

How to Enter Unlock Codes on a Samsung A117, A137, A167, A177, A237, A257 (Magnet), A436, A437, A517, A637, A657, A707, A717, A727, A737, A747 (SLM), A757, A767 (Propel), A777, A787, A797 (Flight), A817, A827 (Access), A837 (Rugby), A867 (Eternity), A877 (Impression), A887 (Sostice), C417, i907 (Epix), X497, ZX10, ZX20, T219, T229, T239, T309, T319, T339, T429, T459 (Gravity), T469 (Gravity 2), T609, T639, T729 (Blast), T739, T749 (Highlight), T819, T919 (Behold), T929 (Memoir)

1) Power on without SIM card

2) Compose: #7465625*638*CODE# (by "CODE" I mean the unlock code I gave you)

Not Yet Personalized - If you see this message, it is another way of saying the phone is already unlocked.

How to Enter Unlock Codes on a A127, P777, D307, D357, D407, D807, T539 (Beat), T629, Z105 and Z107:

1) Power on without SIM card

2) Compose: #0111*CODE# (by "CODE" I mean the unlock code I gave you)

Not Yet Personalized - If you see this message, it is another way of saying the phone is already unlocked.

How to Enter Unlock Codes on Samsung (all other models):

1) Switch ON your phone with a not accepted SIM card

2) Phone will ask for the "Password"

3) You can now enter the unlock code

Not Yet Personalized - If you see this message, it is another way of saying the phone is already unlocked.

How to Enter Unlock Codes on Treo 180, 270, 750

Switch ON your phone without SIM card

Compose : *#*#CODE# (substitute the word "code" with the unlock code we gave you).

OR

Switch ON your phone with a not allowed SIM card.

Enter the unlock code.

Important Note: On some models the Num Lock is not automatically enabled so make sure it is ON before entering the unlock code.

How to Enter Unlock Codes on Treo 750

Insert a not allowed SIM card.

Place the battery and the cover, windows will boot automatically.

Turn on the phone by pressing the front upper-right red button on the keypad.

The phone will ask for the unlock code.

Pull ou tthe stylus pen at the back of the phone, tap the keyboard icon at the center-bottom of the screen.

Enter the unlock code by tapping your stylus pen on the screen keyboard. Then tap OK.

Your Palm Treo phone should be unlocked by now.

OR

Switch ON your phone with allowed SIM card.

Go to menu and select "Phone Tool" or "Phone Application".

Type on virtual keyboard *#*#CODE# (substitute the word "code" with the unlock code we gave you).

Select with PEN "Number" and phone will show that it's unlocked.

OR

Power on with Non-Cingular SIM

using physical keyboard hold down key with large white dot ( lower left hand corner of keyboard ) while typing numbers on the keyboard.

How to Enter Unlock Codes on Treo 650, 680

Remote Treo battery, unplug cable.

Insert incorrect not allowed SIM card (one the phone does not accept)

Power on your Treo, "Sim not allowed" is displayed, click "ok".

Go to the dial pad, and use the stylus to enter code *#*#CODE#. Then press ”Dial“. (substitute the word "code" with the unlock code we gave you). 

Phone will reset and display "sim lock removed"

Ensure you enter the codes in this manner *#*#CODE# (e.g. *#*#12345678#)

Troubleshooting:

Error Message: "The SIM Lock has NOT been removed from this phone"

Solution 1: Please make sure you are entering the correct code and enter it using this method *#*#CODE# dial

Solution 2: If the phone says that the SIM lock has not been removed, ensure that the phone radio (wireless mode) is on.

Unlock Conde Entry Instructions (iPaq 6315, 6325, 6300, 6515, etc)

Insert NON Cingular SIM into device

Power on the device

- Wait approximately 30 seconds until the SimLock application appears (the delay may be longer if the user has already attempted an unlock with the wrong code)

Enter the unlock code in the blank field

Press Ok

- If the unlock code is incorrect, an error dialog will appear.

After pressing Ok on this dialog, the user has to re-enter the unlock code after delays (see above in Device Specific Information)

- If the unlock code is correct, a success dialog will appear.

Press Ok

- The device is now unlocked and should continue booting

OR

On the Today screen, tap Start > Settings.

Tap the Phone Band icon.

The the keyboard icon to open the virtual keyboard

Tap Shift and then Ctl key to enable the keys

Tape the blank area below the band selection box to open the unlock tool.

Tap Shift and then Ctl to disable the keys

Enter the 8-digit unlock code and tap OK when done

Wait for the device to validate the unlock code (about five seconds). You will see one of the following screens:

- Unlock successful

- Unlock failed due to incorrect code. The user has three attempts to unlock. After three attempts, the device will refuse any more unlocking attempts. Perform a soft reset to reset the counter to perform additional attempts.

- Device is not ready for unlocking. This error message displays when the user tries to unlock when the phone applicatoin (not the device) is in a steady state. It takes 30 seconds after powering on the phone for it to reach a steady state.

*If you already have an unlock code and sim card but when you input code, it always says " unlock code not accepted, you have tried...." You must update your ROM version . About 5% hp 6315 have this problem.

This problem can easy be resolved with this ROM update ( ROM v1.00.38)

This rom update will remove all T-mobile logos and sofware and your 6315 will become OEM 6315

dowload here : http://rebootitsmagic.com/ipaq/SP29760_6315.zip

1. Unzip/Extract it using your unzip program (i.e. WinRAR, WinZip, 7zip, etc...)

2. Place the h6315 in cradle. connect it to USB and charger

3. Double click on the hpRUU.exe to run the program

4. View the Readme and if you wish to proceed Agree to the Terms and Conditions

5. Click Next

6. Click Next again to flash the device with the new ROM

How to Enter Unlock Code on Sony Ericsson Cell Phones (all models):

If your phone has a "JOGDIAL" (for example SonyEricsson K700i), then you must press the "down arrow" instead of the "left arrow" for step 3 & 5. By "Down Arrow" I mean directing the Jogdial down!

For the unlocking of a locked  Sony Ericsson no sim card is required.

Turn on the handset.  Display will indicate ”Insert SIM.“

Press the left Arrow (<) button.

Press the star (*) button twice.

Press the left Arrow (<) button again. 

You will briefly see one of the following messages listed on devices display: ”Personalized with MNC2“ or ”Personalized with MNC3“. 

Wait approximately three seconds.

The display will indicate ”Network“ and a picture of a closed lock.

Press Select.

The display will indicate ”Unlock (Net) 5“ and ”NCK:“

Enter the 16 digit NLCK4U code (unlock code we provided you) and press okay.

The handset will display ”Network unlocked“ and the display ”Insert SIM“ appears.

The handset is successfully unlocked.

How to Enter Unlock Code on LG

With a not allowed sim card in your phone enter Pin code then validate, type: 277634#*#

Select 'Sim Unlock' menu #

Enter NCK code then validate How to Unlock LG (most models):

Insert not-allowed SIM card

Power on the handset- phone will display "phone restricted"

Select "Cancel" - phone will display "phone restriction code"

Enter the SIM unlock code

Select "OK" - the handset is now successfully unlocked

Unlock Instruction for LG TU720 (SHINE)

Power ON your phone with not allowed sim card (one that didn't come with the phone)

Type *#865625#

the phone will ask you to input the unlock code twice, just input the unlock code

Device is now unlocked

How to Unlock LG KG800 or TG800 Chocolate

With the phone in standby, enter 2945#*7101#. This will activate the extra menu.

Go to: Settings>Security>SimLock>Network

Select deactivate. Enter the unlock code

How to Unlock LG C2000

Insert non-Cingular SIM card

Power on the handset - phone will display "phone restricted"

Select "Cancel" - phone will display "phone restriction code" 

Enter the SIM Unlock code 

Select "OK" - the handset is now successfully unlocked

How to Enter Unlock Codes on LG F2250

With allowed sim card in the start menu type: 2945#*3311#.

Handset shows saved, then return to startup screen

Press Menu key, choose Settings > Security > Sim Lock> Network > Deactivate, handset will now show 'Enter NCK'

Enter your unlock code and OK.

How to Enter Unlock Codes on LG U8150

Switch ON your phone with a not allowed SIM card.

Compose: 277634#*#

go to menu "SIM Lock".

Enter the unlock code

How to Enter Unlock Codes on LG U8110

Your phone is now unlocked.

How to Enter Unlock Codes on LG U8210

With a not allowed sim card enter Pin code then validate, type: 277634#*#

Shows test menu

Choose sim test menu and type: 2945#*#, choose Sim Unlock menu

Handset shows 'Enter NCK'

Enter code, then hit OK.

How to Enter Unlock Codes on LG U81xx

To bring up the unlock menu on the phone with a SIM card, type 2945#*88110#

Enter the code

In case you need to reset the phone without a SIM card first, type 277634#*# or 47328545454#.

How to Enter Unlock Codes on Cingular AT&T LG CU500

Insert non-Cingular SIM card.

Power on the handset. Phone will display "Invalid SmartChip"

(IF THE PHONE DOES NOT DISPLAY INVALID SMARTCHIP, PLEASE POWER OFF AND ON AGAIN)

In idle screen, enter 159753#*#. Phone will display "Enter NCK, Remaining 5"

Enter the 8 digit SIM unlock code

Select "OK". The handset is now successfully unlocked.

How to Enter Unlock Codes on all other LG cell phones

Switch ON your phone with an allowed SIM card

Then compose:

2945#*5101# -  (if you have a LG 510w)

1945#*5101# -  (if you have a LG 1200 & B1200)

2945#*5221# -  (if you have a LG 5200 & 52200)

2945#*5301# -  (if you have a LG 5300)

2945#*5401# -  (if you have a LG 5400)

2945#*70001# - (if you have a LG 7020)

2945#*7101# -  (if you have a LG 7100)

2945#*1201# or 2945#*70001# - (if you have a LG 1100)

2945#*70001# -  (if you have a LG7250T)

2945#*2201# -  (if you have a LG C2200)

2945#*5301# -  (if you have a LG T5100)

2945#*3311# -  (if you have a LG C3310)

Go to "Menu" and then to "Settings"

Then select "Security"

To finish select "Network Provider" and select "Deactivate"

Enter the unlock code

If your cell phone is not listed, please follow instructions for LG C2000 above

How to Enter Unlock Codes on LG KE970 Shine

Switch ON your phone with an allowed SIM card

Then compose: 2945#*9701#

Press CALL.

It should you ask you for the code.

How to Enter Unlock Codes on CU575 / Trax

Put a non cingular sim in the phone ,phone says invalid smart chip

Now enter *#865625# then select option 1 and then again select 1 and enter your 16 digits code

How to enter codes for HTC, Pantech, Cingular, HP, 8525, 3125, 2125 & all Windows Smartphones, Windows Pocket PC Phones

Power on with incorrect sim, enter unlock code when prompted

Enter code using onscreen keyboard when unlocking a Pocket PC Phones

Switch ON your phone with a not allowed SIM Card,

Phone should show "Enter Special or Subsidy Code",

Enter unlock code

Your phone is now unlocked.

WARNING: if any of these messages appear :

- "Contact Service Provider"

- or "Tamper Alter"

- or "Wait Before Enter Special Code"

- or "Contact Service'

It's because you or somebody else has already entered too many wrong codes. You just have to leave the phone ON on the error message and after 1hr - 8hrs the message "Enter Special Code" will appear again!

Note: If your phone is on a 3G network enter **057*, then another window will appear to enter the unlock code.

How to Enter Unlock Codes on Motorola CDMA and TDMA:

Press 74663 # [Menu] [Menu] and you will be asked for a subsidy code.

Enter unlock code

Your phone will be unlocked instantly.

How to Enter Unlock Codes on Motorola MPX:

I will supply you with 2 unlock codes. One will be the NETWORK PIN and the other the SERVICE PROVIDER PIN.

Switch ON your phone with a not allowed SIM Card,

If phone is asking for NETWORK PIN enter the NETWORK PIN we sent you

If phone is asking for SERVICE PROVIDER PIN. Enter the SERVICE PROVIDER PIN we sent you. 

Your Phone should now be unlocked.